Exactly How to Install a Bath Tub in Your Bathroom
Exactly How to Install a Bath Tub in Your Bathroom
Blog Article
We have stumbled on the article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the net and felt it made sense to write about it with you on this page.
Mounting a bath tub isn't specifically rocket science, yet it does need solid plumbing, woodworking, as well as occasionally, tiling abilities. Changing an old bathtub with a new one is also a moderately challenging job. If the old bathtub is conveniently obtainable, the task can relocate speedily; if you have to open a wall to remove the old tub and position the new bathtub, the task is much harder. In either case, the project is within a home handyman's skills, although you will need a helper to vacate the old bathtub and also embeded in the brand-new one. See to it you have actually certified on your own for the task as well as fit attempting it. Instead of employing a specialist to take over a halfway-completed project, it is better to consider using one before you begin. Chances are you may require a specialist plumber to make tube links.
This article will assist you set up a new bathtub in your bathroom if you have already bought a brand-new bathtub as well as don't need to transform the setup of your previous water pipelines.
Your tools and also product list should consist of the following:
Planning for the Installment
First of all, the supporting structure provided with the bath should be fitted (if called for) according to the maker's instructions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to prevent pressure on the tub.
Fit the versatile faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you use all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its final position.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water supply. After doing so, activate the faucets to drain any type of water remaining in the system. The procedure of removing the existing faucets can be fairly bothersome as a result of the limited gain access to that is usually the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a cloth prepared for the remaining water that will certainly originate from the pipelines. As soon as the supply pipes have actually been gotten rid of, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning throughout this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any kind of old securing compound.
Before carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.
Installing the Bathtub
Using both wood boards under its feet, position the bath tub in the required setting. The wooden boards are handy in evenly spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four little points.
The next objective is to make certain that the tub is leveled all round. This can be accomplished by examining the level as well as changing the feet on the bath tub up until the level checks out level.
To install faucets, fit all-time low of the outermost adaptable tap connector to the proper supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Switch on the water system and also check all joints and new pipework for leaks as well as tighten them if essential. Fill the tub as well as also check the overflow electrical outlet and the normal electrical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the supplier's user's manual. Tiling and sealing around the bathtub needs to wait till the tub has actually been made use of a minimum of once as this will certainly resolve it into its last placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin ensuring that the washing machines are in area between the tap and also the sink. Protect the faucet in place with the manufacturer supplied backnut. As soon as the tap is firmly in position, the supply pipes can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular faucet ports. The former type ought to be connected to the faucet finishes initially, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the location where the bathroom satisfies the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to crack a stiff seal, triggering the water to pass through the wall in between the bath and the tiling, leading to problems with dampness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your fixtures and fittings. They are offered in tubes as well as cartridges, and also are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealer can break relatively very early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the marketplace. It is suggested to fit the tiles utilizing waterproof or water-proof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that piece of writing on How to Install a Bathtub while doing a lookup on the search engines. Sharing is good. Helping others is fun. Thanks for your time. Come back soon.
Details Here Report this page